Show All ItemsThis is a simple wine rack made from the end section of a pallet. This can be made in around an hour and a half depending on what tools you use. You can make it with hand tools and a drill but is a lot easier with power tools. It's simple, easy and cheap to make, and women love them. Step 1: Cutting the PalletShow All ItemsUse a circular saw or hand saw and cut in the indention of the pallet where fork lift forks go. The height of the wine rack will be roughly 16-17 inches tall depending on where you cut it. Step 2: Pulling Boards Off for the BottomShow All ItemsYou'll need two boards for the bottom of the wine rack, you can use the center of the pallet to get these boards. Using a hammer and a pry bar or whatever you have to get in between the boards, hammer it in and pry them off. This may take some practice and be frustrating because the ends have a tendency to crack and break, but eventually you'll get the hang of it or get quality wood that wont crack. Step 3: Cutting Small Pieces Show All ItemsYou'll need 3 smaller pieces to separate the board that holds the glasses and supports the bottom.

You can get these by cutting up the bigger section of pallet that the boards are nailed in to. The pieces need to be the length of the board and 1x1 or a little bigger if you'd like. You can use a hand saw to cut them up or whatever you have. I used a circular saw to cut them off the pallet then used a band saw to cut them to dimension. Step 4: SandingShow All ItemsPallets are usually rough so I sand them down to make them look better and prevent getting splinters. Depending on how rough it is, I just used 120 grit and then 220 grit to finish. Step 5: Holes for the GlassesShow All ItemsOn one board you need to make holes for the wine glasses. Most pallets are going to be around 40 inches wide and i used around the standard size wine glass but you can make the sizes fit your needs. For mine, I mark 4.5 inches in from the edge and then mark 3 more holes of that one 4 inches from the next. The depth I make them is 1.5-1.75 inches into the board. Then I do the same to the other side.Step 6: Drilling the HolesShow All ItemsI use a 1-3/8 inch forstner bit on my drill press but you can use a hand drill if you don't have one, and drill out your marked holes.

Step 7: Cutting Gaps for the GlassesShow All ItemsI just use a piece of wood around and inch wide, center it on the hole and mark where I need to make the cuts. the best bc winesUsing whatever saw you have, cut the pieces out and sand the rough edges. top wine shops parisStep 8: Putting It TogetherShow All ItemsI put the boards together and line them up with the bottom of the rack to make sure everything goes together well. best red wine for christmas gift 2015I clamp them to my table and pre drill the holes and counter sink them. red wine name with regionI use 3 inch screws to put it all together but you can use smaller screws and put it together in sections if you'd like. wine of fire usa

Make sure you pre drill all your holes either way so it doesn't split the wood. best wine bar soho londonStep 9: Finished, HangingShow All ItemsThe wine rack is done, now all you have to do it hang it. I use 2, 2.5 inch screws and put them in studs because all the weight from the wine bottles. Depending on where you're hanging it and the studs location, I put them in one stud, skip one and put them in the other so there's 32 inches between screws. Make sure you use a level before putting in the second screw.Building a wine cellar in your basement is a formidable task; however, the rewards are considerable. For every dollar invested in building a wine cellar, you will easily see a $3 return in increased property value. Plus, as a wine enthusiast, creating a cellar allows you to store your wine under proper conditions over a period of many years. Follow these instructions to add a wine cellar to your basement.

It is a major do-it-yourself project. For an average-sized wine cellar, a professional contractor will charge anywhere from $50,000 to $60,000. Additionally, if a cellar construction includes excavation and concrete pouring, the price can soar upwards. You will need to determine a realistic budget that will dictate the type and size you can afford building it yourself. If you decide to build a room that accommodates not only storage, but also dining and tasting, you will need to double the space. A traditional wine storage cellar only is a 10x10-foot room with enough wall space to store 1,600 bottles of wine. Purchase a wine cellar air conditioner that can properly preserve and mature your wine selection. Optimum room temperature is 55-59 °F. Additionally the room humidity must be between 60% and 70%. Due to the unusual temperature and humidity requirements, normal home air conditioning units will not work. Depending on your needs or desires, you can choose between a wall unit, a split system controlling temperature and humidity, or a duct system with no appliance inside the room.

It all comes down to budget and aesthetics. Use 2x6-inch lumber to frame your wine cellar walls. This size lumber is necessary to contain R-19 insulation, which maintains a consistent temperature. Don’t fret if you are using 2 existing walls that employ 2x4-inch lumber. Locate your wine cellar room where 2 existing walls can be used. If any existing walls are concrete, you will need to construct a 2-sided frame and attach it to the existing wall Staple the plastic sheeting to the outside walls, which is commonly referred to as the warm side of the wall. The plastic acts as a vapor barrier. If you have 2 existing walls and cannot access the outside, attach the plastic to the inside area. If the walls are concrete, first attach an anchor strip equal to the length of the desire room over the top and at the bottom of each existing concrete wall. While your wine cellar walls are open, install all necessary wiring. Make sure to install it according to your local codes.